Globe Valve,1",3 Way,14 Cv,w/ Electronic Fail-Safe,24V,Modulating| Actuator Type | Electronic fail-safe |
|---|
| Close Off Pressure | 250�psi |
|---|
| End Fitting | Internal thread |
|---|
| Controllable Flow Range | stem up - open B to AB |
|---|
| Electrical Connection | cable |
|---|
| ANSI class body | ANSI 250 (up to 400 psi below 150�F) |
|---|
| Application | This valve is typically used in Air handling units on heating or cooling coils, and fan coil unit heating or cooling coils. Some other common applications include Unit Ventilators, VAV box re-heat coils and bypass loops. This valve is suitable for use in hydronic system with constant or variable flow. 3-way valves are available with mixing or diverting flow patterns |
|---|
| Service | chilled, hot water, up to 60% glycol |
|---|
| Flow Characteristic | linear |
|---|
| Controllable Flow Range | stem up - open B to AB |
|---|
| End Fitting | NPT female ends |
|---|
| Stem Packing | spring loaded Teflon? V-ring |
|---|
| Body Pressure Rating [psi] | ANSI 250 |
|---|
| Media Temperature Range (Water) | 20�F to 280�F [-7�C to 138�C] |
|---|
| Max Differential Pressure (Water) | 35 psi (241 kPa) |
|---|
| Servicing | Repack/Rebuild kits available |
|---|
| Power Supply | 24 VAC � 20%, 50/60 Hz, 24 VDC � 10% |
|---|
| Power Consumption Running | 3 W |
|---|
| Power Consumption Holding | 2 W |
|---|
| Transformer Sizing | 7 VA (class 2 power source) |
|---|
| Electrical Connection | 3 ft, 18 GA plenum rated cable with 1/2?conduit connector protected NEMA 2 (IP54) |
|---|
| Overload Protection | electronic throughout full stroke |
|---|
| Input Impedance | 100 k ? for 2 to 10 VDC (0.1 mA), 500 ? for4 to 20 mA |
|---|
| Direction of Rotation (Motor) | reversible with switch |
|---|
| Manual Override | 4 mm hex crank (shipped w/actuator) |
|---|
| Running Time (Motor) | 90 sec, constant independent of load |
|---|
| Ambient Temperature Range | -22�F to 122�F [-30�C to 50�C] |
|---|
| Storage Temperature Range | -40�F to 176�F [-40�C to 80�C] |
|---|
| Housing | NEMA 2, IP54, UL enclosure type 2 |
|---|
| Agency Listings | cULus acc. to UL60730-1A/-2-14, CAN/CSA
E60730-1:02, CE acc. to 2004/108/EC and
2006/95/EC |
|---|
| Noise Level (Motor) | <45 dB (A) |
|---|
| Operating Range Y | 2 to 10 VDC, 4 to 20 mA w/ ZG-R01 (500 ?,1/4 W resistor) |
|---|
| Direction of Rotation (Fail-Safe | reversible with switch |
|---|
| Position Indication | stroke indicator on bracket |
|---|
| Running Time (Fail-Safe) | 35 sec |
|---|
| Noise Level (Fail-Safe) | <60 dB (A) |
|---|
| Feedback Output U | 2 to 10 VDC |
|---|
| Housing Material | Aluminum die cast and plastic casing |
|---|
| Electrical protection | actuators are double insulated |
|---|
| Humidity | 5 to 95% RH non-condensing |
|---|
| ANSI Class | ANSI 250 ( up to 400 psi below 150�F) |
|---|
| Rangeability | A-port 100:1, B-port 500:1 |
|---|
| Stroke | 0.6? [15 mm] LV, 3/4? [20 mm] SV |
|---|
| Linear Force | 337 lbf [1500 N force] |
|---|
| Bridge Time | 2 sec delay before fail-safe activates |
|---|
| Pre-charging Time | 5 to 20 seconds |
|---|
| Piping | The valves should be mounted in a weather-protected area in a location that is within the ambient limits of the actuator. Allow sufficient room for valve with actuator and for service. The G2(S) and G3(D) preferred mounting position of the valve is with the valve stem vertical above the valve body, for maximum life. However, the assemblies can be mounted with the valve stem vertical or horizontal in relation to the pipe. The actuators should never be mounted underneath the valve, as condensation can build up and result in a failure of the actuators. Do not reverse flow direction. |
|---|
Product Family
All orders are shipped same-day if the order is received by 1:00 PM Central Time. We ship worldwide.
UPS Hoilday Delivery Schedule
For more infomation about Returns visit Returns
For more informatrion about Warranty visit Warranty page.
You can also find answers to some common questions on our FAQ page
Reviews
Not reviewed yet, be the first to write one!
Add Review
|